Nie masz w koszyku żadnych produktów
 
English Polski Spanish 
Szukaj instrukcji do
 

(e.g. AA-V20EG JVC, ZX-7 Sony )
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Kto jest w sklepie?
Sklep przegląda 5965 gości 
Kategorie
Informacje
Polecamy
Strona główna >> SONY >> SPPSS966 Instrukcja Serwisowa
 
 0 szt. w koszyku 

SONY SPPSS966
Instrukcja Serwisowa


Tweetnij o tym produkcie a dostaniesz $1.00 rabatu!
  • Zawiera schematy
  • Plik do pobrania
  • Format PDF
  • Kompletna instrukcja
  • Język: English
Cena: $4.99

Opis SONY SPPSS966 Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schematy, diagramy drukowanych obwodów (PCB), schematy połączeń, schematy blokowe oraz katalog części. Instrukcje serwisowe są wykorzystywane glównie przez osoby naprawiające uszkodzony sprzęt.

Jeśli chcesz się dowiedzieć jak się obsługuje Twój telewizor, magnetowid, odtwarzacz mp3 itp. powinieneś raczej szukać instrukcji obsługi

Instrukcja jest dostępna w następujących językach: English

Plik nie jest jeszcze gotowy
Musisz najpierw dokonać zakupu.

Recenzje produktu
Dla tego produktu nie napisano jeszcze recenzji!
Recenzje innych produktów
 SA-A30E AIWA Instrukcja Serwisowa by Adam Grążka;
Wszystko w porządku. Instrukcja czytelna i kompletna. Dziękuję. all right! thank you.
 KX990SR KENWOOD Instrukcja Serwisowa by Viktor Kapeć;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
 TA2760 ONKYO Instrukcja Serwisowa by Viktor Kapeć;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
 26PF3302/10 PHILIPS Instrukcja Serwisowa by Ryszard Burzak;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
 DX666 AIWA Instrukcja Serwisowa by Adam Grążka;
...instrukcja serwisowa w pełni czytelna i kompletna. Dziękuję!

Tekstowy podgląd strony 23 (kliknij aby zobaczyć)
6-2. HANDSET SECTION
� Make the set in Test mode (see page 19)

3. Checking TX output Setting:
peak power meter

1. Checking RX I&Q Output Level Setting:
oscilloscope + � level meter + � TP520: RXIP TP521: RXIN TP522: RXQP TP523: RXQN TP553: GND

+ �

ANTENNA TERMINAL

SSG

ANTENNA TERMINAL

Procedure: 1. Place the handset in the Continuous Transmit mode (CH1, High power). 2. Measure the ANT OUT output of the RF module in the handset using a peak power meter. 3. Confirm that the measured output is 80 mW (MIN 20 mW). 4. Also, execute steps 1 through 3 for the channels 10 and 20. CH10: 80 mW (MIN 20 mW) CH20: 50 mW (MIN 10 mW)

Procedure: 1. Place the handset in the Continuous Receive mode (CH1, LNA, AGC ON). 2. Set the SSG frequency to the frequency on CH1 + 300 kHz, and the RF output level to �95 dBm. 3. Measure the output level of RXIN, RXIP, RXQN, and RXQP with a level meter. At this time, confirm with an oscilloscope that a sine wave of 300 kHz is output. 4. Confirm that the measured output level is �31.0 to �24.0 (TYPICAL �27.0) dBV. If IC502 was replaced (there is no ID data), the output level is �31.0 to �24.0 dBV. 5. Also, execute steps 1 through 4 for the channels 10 and 20. * For the frequency on each channel, see page 15.

2. Checking TX Center Frequency Setting: � short: TP555 � TP553
frequency counter + � ANTENNA TERMINAL

Procedure: 1. Short TP555 and TP553 (GND) on the HAND MAIN board in the handset. 2. Place the handset in the Continuous Transmit mode (CH1, High power). 3. Measure the ANT OUT frequency of the RF module in the handset using a frequency counter. 4. Confirm that the measured frequency is 903.600 MHz ± 27 kHz. 5. Also, execute steps 1 through 4 for the channels 10 and 20.

23

Klienci kupując ten produkt kupili także

$4.99

SPPSS966 SONY
Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email…
>
Parse Time: 0.164 - Number of Queries: 117 - Query Time: 0.039