Nie masz w koszyku żadnych produktów
 
English Polski Spanish 
Szukaj instrukcji do
 

(e.g. AA-V20EG JVC, ZX-7 Sony )
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Kto jest w sklepie?
Sklep przegląda 5917 gości 
Kategorie
Informacje
Polecamy
Strona główna >> SONY >> MZR37 Instrukcja Serwisowa
 
 0 szt. w koszyku 

SONY MZR37
Instrukcja Serwisowa


Tweetnij o tym produkcie a dostaniesz $1.00 rabatu!
  • Zawiera schematy
  • Plik do pobrania
  • Format PDF
  • Kompletna instrukcja
  • Język: English
Cena: $4.99

Opis SONY MZR37 Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schematy, diagramy drukowanych obwodów (PCB), schematy połączeń, schematy blokowe oraz katalog części. Instrukcje serwisowe są wykorzystywane glównie przez osoby naprawiające uszkodzony sprzęt.

Jeśli chcesz się dowiedzieć jak się obsługuje Twój telewizor, magnetowid, odtwarzacz mp3 itp. powinieneś raczej szukać instrukcji obsługi

Instrukcja jest dostępna w następujących językach: English

Plik nie jest jeszcze gotowy
Musisz najpierw dokonać zakupu.

Recenzje produktu
Dla tego produktu nie napisano jeszcze recenzji!
Recenzje innych produktów
 ST-8077K TECHNICS Instrukcja Serwisowa by Adam Grążka;
...instruction is ok. ...instrukcja jest ok. Thanks/Dzięki
 T5 SANSUI Instrukcja Serwisowa by Adam Grążka;
Documentation made ​​available quickly and It is good quality. Thanks.

Tekstowy podgląd strony 5 (kliknij aby zobaczyć)
SECTION 2 SELF-DIAGNOSTIC
2-1. GENERAL
This set uses the self-diagnostic system in which if an error occurs in playback/recording mode, the error is detected by the model control and power control blocks of the microprocessor and information on the cause is stored as history in EEPROM. By viewing this history in test mode, it helps you to analyze a fault and determine its location. 2) Remote controller LCD

888

ı

All ON

2-2. TEST MODE SETTING
There are two different methods to set the test mode: 1 Short BP801 (TEST) on the main board with a solder bridge (connect pin @§ of IC801 to the ground). Then, turn on the power.
MAIN BOARD (SIDE B)

All OFF

Vr. 1.��

Microprocessor version display
X801

IC801

� Holding down P allows the current display to be maintained while it being depressed.

2-4. RELEASING THE TEST MODE
25 26

For test mode set with the method 1: Turn off the power and open the solder bridge on BP801 on the main board. For test mode set with the method 2: Turn off the power.

BP801 (TEST) IC301

C401

2-5. SELF-DIAGNOSTIC MODE
1. Go into the test mode. 2. With the unit LCD indicators all flashing, press DISPLAY key to go into the self-diagnostic mode.

2 In the normal mode, use the keys on the unit to perform the following operations: Press and hold down ( and press the keys below in this turn: + n + n =n = n + n = n + n =nPnP

1st0 00

2-3. OPERATION IN TEST MODE SETTING
When the test mode is set, the LCD shows repeated cycles of the following display: 1) Unit LCD

Error indication code History code

3. Then, each time ) key is pressed, the reference information display changes as given below.

1st

� 1 2 � 1 2

XX �� �� XX �� ��

N-1 N-1 N-1 N-2 N-2 N-2 R 1st

� 1 2 � 1 2

XX �� �� XX �� �� XXXX

ı 188:88 pppppp

All ON

1st 1st
All OFF

N N

Microprocessor version display

N

Vr. 1.00

�

XX

(return)

� Press = key to go back to the previous display.

�5�

Klienci kupując ten produkt kupili także

$4.99

MZR37 SONY
Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email…
>
Parse Time: 0.227 - Number of Queries: 105 - Query Time: 0.048