Nie masz w koszyku żadnych produktów
 
English Polski Spanish 
Szukaj instrukcji do
 

(e.g. AA-V20EG JVC, ZX-7 Sony )
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Kto jest w sklepie?
Sklep przegląda 5968 gości 
Kategorie
Informacje
Polecamy
Strona główna >> SONY >> MZE35 Instrukcja Obsługi
 
 0 szt. w koszyku 

SONY MZE35
Instrukcja Obsługi


Tweetnij o tym produkcie a dostaniesz $1.00 rabatu!
  • Plik do pobrania
  • Format PDF
  • Kompletna instrukcja
  • Język: English, French
Cena: $4.99

Opis SONY MZE35 Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email po jego zakupieniu.

Instrukcje obsługi (czasami nazywane także podręcznikiem użytkownika) opisuja funkcje i sposób działania danego produktu.

Instrukcja jest dostępna w następujących językach: English, French

Plik nie jest jeszcze gotowy
Musisz najpierw dokonać zakupu.

Recenzje produktu
Dla tego produktu nie napisano jeszcze recenzji!

Tekstowy podgląd strony 5 (kliknij aby zobaczyć)
SECTION 3 TEST MODE
General � In the TEST mode, this set provides the Auto mode in which both CD and MO are adjusted automatically. In the Auto mode, whether a disc is CD or MO is discriminated, then each adjsutment is automatically executed sequentially. If a fault is found, it is displayed. Also, in the Servo mode, each item can be adjusted automatically. Entering TEST Mode Bridge the TAP801 (TEST) on MAIN board (connect IC801 #� to GND), and turn the power on. Then, press ( key and the TEST mode is activated. Releasing TEST Mode Turn the power off, and remove the bridge from TAP801 (TEST) on MAIN board. Operation in TEST Mode In the TEST mode, the LCD display is as shown below:
( ) for Remote controller LCD display

Configuration of TEST Mode The TEST mode configuration of this set is as follows:
+key
pkey

AUTO Mode (key (Auto?)
pkey

(Start?)
pkey

�key
pkey

MANUAL Mode (Manu?)

(key

SERVO Mode

000
+,�key AUDIO Mode

100
+,�key POWER Mode

300

300

Main unit LCD

300

V3.000

ROM version display (Ver3.00 or Ver3.20)

Remote controller LCD

SERVO Mode � Enter the TEST mode, press VOL � key and ( key to select the SERVO mode. � When the second digit of mode number is not 0 and the first digit is 0 (010, 020, 030, etc.), the optical pickup moves to outside track or inside track with + key or = key respectively. � To select other modes, refer to the TEST mode configuration. 1. Configuration of SERVO Mode
SERVO Mode
(key

Display in TEST Mode

� ROM version display � All ON � All OFF are repeated. � To hold the display for confirmation, press the PLAY MODE key.

000
pkey

+,�key

OFFSET Adj.

(key

010
Each time (key is pressed, 011-013 modes pkey are switched. (For each mode, see relevant table)
(key

pkey

LASER POWER Adj.

(key

020
Each time (key is pressed, 021-024 modes pkey are switched. (For each mode, see relevant table)
(key pkey

MO Adj.

(key

030
Each time (key is pressed, 031-039 modes pkey are switched. (For each mode, see relevant table)
(key

1

2
(To page 9 )

3

�8�

+,�key

Klienci kupując ten produkt kupili także

$4.99

MZE35 SONY
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…
>
Parse Time: 0.163 - Number of Queries: 100 - Query Time: 0.037