|
|
|
Kto jest w sklepie?
Sklep przegląda 5954 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
KP-51WS510/57WS510/65WS510
2-4. FOCUS LENS ADJUSTMENT
In this adjustment, use the remote commander while in service mode. For details on the usage of the service mode and the remote commander, please refer to section 2-10. ELECTRICAL ADJUSTMENTS BY REMOTE COMMANDER. 1. Loosen the lens screw. 2. Cover the red and blue CRT lenses with lens caps to allow only green to show (or use the method shown in the note below for turning off the CRTs individually without using lens caps). 3. Turn the green lens to adjust to the optimum focus point with the crosshatch signal. 4. Tighten the lens screw. 5. Cover the green and blue CRT lenses with the lens caps to allow only red to show (or use the method shown in the note below for turning off the CRTs individually without using lens caps). 6. Turn the red lens to adjust to the optimum focus point with the crosshatch signal. 7. Tighten the lens screw. 8. Cover the green and red CRT lenses with the lens caps to allow only blue to show (or use the method shown in the note below for turning off the CRTs individually without using lens caps). 9. Turn the blue lens to adjust to the optimum focus point with the crosshatch signal. 10. Tighten the lens screw. 11. After adjusting the items: 2-5. FOCUS VR ADJUSTMENT, 2-6. 2-POLE MAGNET ADJUSTMENT, 2-8. 4-POLE MAGNET ADJUSTMENT, Reconfirm the optimum focus point and adjust again if necessary. * Every time 6 is pressed, the test signal changes to: �crosshatch+video signal� � �crosshatch+borderline (black)� � �crosshatch (black)� � �dots (black)� � off
2-5. FOCUS VR ADJUSTMENT
1. Set generator to crosshatch. 2. Cover the red and blue CRT lenses with lens caps to allow only green to show (or use the method shown in the note below for turning off the CRTs individually without using lens caps). 3. Turn the green focus VR on the focus block to adjust to the optimum focus point with the crosshatch signal. 4. Cover the green and blue picture lenses with lens caps to allow only red to show (or use the method shown in the note below for turning off the CRTs individually without using lens caps). focus point with the crosshatch signal.
5. Turn the red focus VR on the focus block to adjust to the optimum 6. Cover the green and red picture lenses with lens caps to allow only blue to show (or use the method shown in the note below for turning off the CRTs individually without using lens caps). 7. Turn the blue focus VR on the focus block to adjust to the optimum focus point with the crosshatch signal. 8. After adjusting the items: 2-4. FOCUS LENS ADJUSTMENT, 2-6. 2-POLE MAGNET AND CENTERING ADJUSTMENT, 2-8. 4-POLE MAGNET ADJUSTMENT, Reconfirm the optimum focus point and adjust again if necessary. Note: If lens caps are unavailable, you can cut off the unnecessary color beams by controlling the service mode 2150P-2 1 RGBS.
Scanning line visible.
A Minimize both A and B.
Lens
B
Center of crosshatch
Test Signal Note: If lens caps are unavailable, you can cut off the unnecessary color beams by controlling the service mode 2150P-2 1 RGBS.
� 16 �
|
|
|
> |
|
